Lyri Calibrations

(A2LA Cert. No. 7608.01) 06/09/2026 Page 2 of 5 Parameter/Equipment Range CMC2, 5 (±) Comments DC Current – Generate & Measure3 Up to 24 mA 0.02 % of rdg + 2 counts Fluke 725 process calibrator Electrical Simulation of Thermocouple3 Type J Type K Type T (-200 to 0) °C (0 to 1200) °C (-200 to 0) °C (0 to 1370) °C (-200 to 0) °C (0 to 400) °C 1.0 °C 0.70 °C 1.2 °C 0.80 °C 1.0 °C 0.80 °C Fluke 725 process calibrator II. Fluid Quantities Parameter/Equipment Range CMC2, 4 (±) Comments Air Velocity – Measuring Equipment3 (0.40 to 10.00) m/s (10.0 to 25.00) m/s (80 to 1965) ft/min (1965 to 4900) ft/min 0.5 meters/sec 0.75 meters/sec 100 ft/min 150 ft/min Anemometer

(A2LA Cert. No. 7608.01) 06/09/2026 Page 4 of 5 IV. Thermodynamics Parameter/Equipment Range CMC2 (±) Comments Thermometers3 (-200 to 200) °C (100 to 1100) °C 1.1 °C 2.0 °C Type J, K, T, bath V. Time & Frequency Parameter/Equipment Range CMC2, 4 (±) Comments Frequency – Measure3 (2 to 1000) CPM (1 to 1100) Hz (1 to 10) kHz Sensitivity 0.05 % rdg + 1 count 0.05 % rdg + 1 count 0.05 % rdg + 1 count 1 V peak-to-peak minimum Fluke 725 process calibrator ________________________________________ 1 This laboratory offers commercial calibration service and field calibration service. 2 Calibration and Measurement Capability Uncertainty (CMC) is the smallest uncertainty of measurement that a laboratory can achieve within its scope of accreditation when performing more or less routine calibrations of nearly ideal measurement standards or nearly ideal measuring equipment. CMCs represent expanded uncertainties expressed at approximately the 95 % level of confidence, usually using a coverage factor of k = 2. The actual measurement uncertainty of a specific calibration performed by the la boratory may be greater than the CMC due to the behavior of the customer’s device and to influences from the circumstances of the specific calibration. 3 Field calibration service is available for this calibration. Please note the actual measurement uncertainties achievable on a customer's site can normally be expected to be larger than the Calibration and Measurement Capability Uncertainty (CMC) found on the A2LA Scope. Allowance must be made for aspects such as the environment at the place of calibration and for other possible adverse effects such as those caused by transportation of the calibration equipment. The usual allowance for the uncertainty introduced by the item being calibrated, (e.g. resolution) must also be considered and this, on its own, could result in the actual measurement uncertainty achievable on a customer’s site being larger than the CMC. 4 The instrument or material being calibrated is defined by the parameter. This indicates the laboratory is capable of calibrating instruments that measure or generate the values in the ranges indicated for the listed measurement parameter.

(A2LA Cert. No. 7608.01) 06/09/2026 Page 5 of 5 5 The stated measured values are determined using the indicated instrument (see Comments). This capability is suitable for the calibration of the devices intended to measure or generate the measured value in the ranges indicated. CMC’s are expressed as either a specific value that covers the full range or as a percent or fraction of the reading plus a fixed floor specification. 6 This scope meets A2LA’s P112 Flexible Scope Policy.