Anritsu Americas Sales Company

(A2LA Cert. No. 2160.05) 07/31/2024 Page 2 of 5 Parameter/Range Frequency CMC2, 5 (±) Comments Power Level – Absolute3, 8 Measure & Generate, Type N & K Connector, Spectrum Analyzer, Measuring Receiver (-35 to 20) dBm (-60 to 20) dBm (-90 to -60) (-35 to 20) dBm (-60 to 20) dBm (-90 to -60) (0.01 to 100) MHz (0.1 to 2) GHz (2 to 12) GHz (12 to 18) GHz (0.01 to 2) GHz (2 to 9) GHz (9 to 13) GHz (13 to 18) GHz (0.01 to 18) GHz (0.01 to 100) MHz (0.1 to 7) GHz (7 to 12) GHz (12 to 17) GHz (17 to 40) GHz (0.01 to 3) GHz (3 to 8) GHz (8 to 12) GHz (12 to 27) GHz (27 to 40) GHz (0.05 to 40) GHz 0.025 dB 0.030 dB 0.045 dB 0.055 dB 0.057 dB 0.063 dB 0.071 dB 0.088 dB 0.17 dB 0.035 dB 0.05 dB 0.06 dB 0.08 dB 0.085 dB 0.057 dB 0.063 dB 0.071 dB 0.088 dB 0.097 dB 0.18 dB Type N power sensor Spectrum analyzer, power sensor with attenuator Type K power sensor Spectrum analyzer, power sensor with attenuator Power Level – Absolute6 Measure & Generate, Type V & Waveguide Connector (-35 to 20) dBm (0.01 to 100) MHz (0.1 to 2) GHz (2 to 8) GHz (8 to 12) GHz (12 to 26) GHz (26 to 40) GHz (40 to 50) GHz (50 to 67) GHz 0.04 dB 0.05 dB 0.06 dB 0.065 dB 0.08 dB 0.09 dB 0.12 dB 0.17 dB Type V power sensor

(A2LA Cert. No. 2160.05) 07/31/2024 Page 4 of 5 III. Mechanical Parameter/Equipment Range CMC2, 7 (±) Comments Torque Wrench (0.25 to 250) lbf.in 2.5 % Torque analyzer IV. Time & Frequency Parameter/Equipment Range CMC2, 6 (±) Comments Frequency – Measuring Equipment 10 MHz reference 1 Hz to 70 GHz4 9 x 10-11 Hz/Hz 1.4 x 10-9 Hz/Hz GPS receiver Synthesizer w/ GPS disciplined oscillator ____________________________________________ 1 This laboratory offers commercial calibration and field calibration services. 2 Calibration and Measurement Capability Uncertainty (CMC) is the smallest uncertainty of measurement that a laboratory can achieve within its scope of accreditation when performing more or less routine calibrations of nearly ideal measurement standards or nearly ideal measuring equipment. CMCs represent expanded uncertainties expressed at approximately the 95 % level of confidence, usually using a coverage factor of k = 2. The actual measurement uncertainty of a specific calibration performed by the laboratory may be greater than the CMC due to the behavio r of the customer’s device and to influences from the circumstances of the specific calibration. 3 Field calibration service is available for this calibration. Please note the actual measurement uncertainties achievable on a customer's site can normally be expected to be larger than the Calibration and Measurement Capability Uncertainty (CMC) found on the A2LA Scope. Allowance must be made for aspects such as the environment at the place of calibration and for other possible adverse effects such as those caused by transportation of the calibration equipment. The usual allowance for the uncertainty introduced by the item being calibrated, (e.g. resolution) must also be considered and this, on its own, could result in the actual measurement uncertainty achievable on a customer’s site being larger than the CMC 4 This scope meets A2LA’s P112 Flexible Scope Policy. 5 The stated measured values are determined using the indicated instrument (see Comments). This capability is suitable for the calibration of the devices intended to measure or generate the measured value in the ranges indicated. CMC’s are expressed as either a specific value that covers the full range or as a percent or fraction of the reading plus a fixed floor specification. 6 The type of instrument or material being calibrated is defined by the parameter. This indicates the laboratory is capable of calibrating instruments that measure or generate the values in the ranges indicated for the listed measurement parameter.

(A2LA Cert. No. 2160.05) 07/31/2024 Page 5 of 5 7 In the statement of CMC, percentages are percentage of reading, unless otherwise indicated. 8 Enlisted values represent absolute power level uncertainty, including test port match.