Gagemaker, LP
712 E. Southmore Avenue, 77502, Pasadena, TX, United States
Visit website- Scope lines
- 4
- A2LA certificate
- 1
- Site in our directory
- 1
What this lab is accredited for
We could not match the method references in this lab’s scope to published test standard numbers. The full scope as published is below.
Only this lab. Searches the method, matrix and range of each of the 4 scope lines.
A2LA certificate 4326.01 · 4 lines
| Line | Method | Matrix | Range |
|---|---|---|---|
| 1 | - | -Show page textExtracted from the scope document; tables may not line up. View scope for the original. (A2LA Cert. No. 4326.01) Revised 11/13/2025 Page 1 of 3
SCOPE OF ACCREDITATION TO ISO/IEC 17025:2017
GAGEMAKER, LP.
712 E. Southmore Ave,
Pasadena, TX 77502
Roger Wolff Phone: 713 472 7360
CALIBRATION
Valid To: November 30, 2027 Certificate Number: 4326.01
In recognition of the successful co mpletion of the A2LA evaluation process (including an assessment of
the organization’s compliance with R205 – A2LA’s Calibration Program Requirements), accreditation is
granted to this laboratory to perform the following calibrations
1, 6:
I. Dimensional
Parameter/Equipment
Range
CMC2, 3 (±)
Comments
Indicators, Diameter,
Width, Thread Height, and
Lead Gages
5
Up to 1 in
64 µin
Gage blocks, MIC
TRAC, CG-1000
Depth Gages
Up to 8 in
(8 to 18) in
(66 + 0.6R) µin
(67 + 36L) µin
MIC TRAC
Rod Standards
Up to 20 in
(43 + 7.8L) µin
Height gage
Frame Standards
Up to 12 in
(12 to 36) in
(63 + 4.4L) µin
(53 + 5.2L) µin
CMM, MIC TRAC
Thread Rolls – Pitch
Diameter
Up to 1 in
82 µin
MIC TRAC, gage wires
Calipers
Up to 12 in
(280 + 11.5L) µin
MIC TRAC, gage
blocks | to 1 in |
| 2 | - | -Show page textExtracted from the scope document; tables may not line up. View scope for the original. (A2LA Cert. No. 4326.01) Revised 11/13/2025 Page 2 of 3
Parameter/Equipment
Range
CMC2, 3, 7 (±)
Comments
Micrometers
Outside
Inside
Depth
Up to 1 travel
Up to 1 travel
Up to 1 travel
32 µin
53 µin
41 µin
MIC TRAC, gage
blocks
MIC TRAC
(Bench Top Micrometer)
Up to 12 in
(12 to 24) in
(24 to 36) in
(36 to 48) in
(48 to 60) in
(60 to 72) in
(20 + 2.5L) µin
(29 + 1.7L) µin
(11 + 2.5L) µin
(22 + 2.2L) µin
(4 + 2.6L) µin
(32 + 2.1L) µin
Renishaw laser
Stator Bore Gages
4
Up to 0.250 in
Up to 0.250 in
650 µin
1500 µin
Micrometer fixture
Cylindrical standards
MIC 360
(Circumference Gage)
5
(3.5 to 6) in
86 µin
Plain plug
Thread Profile – (2 to 20)
Pitch
Up to 6 in
Up to 6 in
270 µin
160 µin
Optical comparator
Keyence IM-7001
Dimensional Length –
Measure
1D
2D
3D
Up to 12 in
(12 to 36) in
Up to 12 in
(12 to 32) in
Up to 18 in
(63 + 4.4L) µin
(53 + 5.2L) µin
(57 + 4.9L) µin
(53 + 5.2L) µin
(64 + 3.8L) µin
MIC TRAC
CMM
Mitutoyo Height Gages
(LH-600E / LH600F)
Up to 24 in
(29 + 0.7L) µin
Mitutoyo check master
__________________________________________________________
1 This laboratory offers commercial calibration and dimensional testing services. | to 1 in |
| 3 | Extracted from the scope document; tables may not line up. View scope for the original. (A2LA Cert. No. 4326.01) Revised 11/13/2025 Page 3 of 3
2 Calibration and Measurement Capability Uncertainty (CMC) is the smallest uncertainty of measurement
that a laboratory can achieve within its scope of accreditation when performing more or less routine
calibrations of nearly ideal measurement standa rds or nearly ideal measuring equipment. CMC’s
represent expanded uncertainties expressed at approximately the 95 % level of confidence, usually using
a coverage factor of k = 2. The actual measuremen t uncertainty of a specific calibration performed by
the laboratory may be greater than the CMC due to the behavior of the customer’s device and to influences
from the circumstances of the specific calibration.
3 In the statement of CMC, L is the numerical value of the nominal length of the device measured in inches;
it represents time, R is the resolution in inches of the unit under test.
4 This range describes the travel of the gage’s measuring arm or mechanism.
5 This range describes the wheel diameter of the MIC 360.
6 This scope meets A2LA’s P112 Flexible Scope Policy.
7 The type of instrument or material being calibrate d is defined by the parameter. This indicates the
laboratory is capable of calibrating instruments that measure or generate the values in the ranges indicated
for the listed measurement parameter. | ||
| 4 | ISO/IEC 17025:2017; R205 | - | - |
Ranges are reproduced from the accredited scope document as published, and only where we found that range printed in the document for the line. Otherwise the cell reads “See scope document”. An absent range means the register did not state one. Line numbers are ours, for cross-reference; they follow the order of the scope document.
Location
Accreditation data refreshed from the A2LA register on .
This page mirrors a public register. For a purchasing, audit or regulatory decision, confirm against the A2LA entry linked above.