IMP Electronic Systems

(A2LA Cert. No. 4741.01) 09/26/2024 Page 2 of 5 II. Electrical – DC/Low Frequency Parameter/Equipment Range CMC2, 4, 5 (±) Comments DC Voltage – Generate 1 mV to 1 V (1 to 10) V (10 to 100) V 100 V to 1 kV (0.002 53 + 6.7 V) µV (4.6 + 2.1 V) µV (-16 + 4.2 V) µV (-160 + 5.6 V) µV Fluke multi product calibrator 5522A DC Current – Generate (0 to 10) mA (10 to 100) mA 100 mA to 1 A (1 to 20) A (0.059 + 12. A) µA (0.12 + 5.8 A) µA (-11 + 120 A) µA (-26 + 150 A) µA Fluke multi product calibrator 5522A DC Resistance (4 Wire) – Generate (0.01 to 100) Ω 100 Ω to 1 kΩ (1 to 100) kΩ 100 kΩ to 1 MΩ (1 to 10) MΩ (10 to 100) MΩ (.64 + 0.011 R) mΩ (0.84 + 0.01 56 R) mΩ (0.67 + 0.01 79 R) mΩ (180 + 0.01 02 R) mΩ (-7550 + 0.015 R) mΩ (-1067 + 0.000 12 R) Ω Fluke multi product calibrator 5522A

(A2LA Cert. No. 4741.01) 09/26/2024 Page 3 of 5 Parameter/Range Frequency CMC2, 4, 5 (±) Comments AC Voltage – Generate (1.0 to <33) mV (33 to <330) mV (0.33 to <3.3) V (3.3 to <33) V (33 to <330) V (330 to 1020) V 10 Hz to 50 kHz (50 to 500) kHz 10 Hz to 50 kHz (50 to 500) kHz 10 Hz to 50 kHz (50 to 500) kHz 10 Hz to 50 kHz (50 to 100) kHz 110 Hz to 50 kHz (50 to 100) kHz 45 Hz to 10 kHz (3.3 + 0.18 V) µV (3.04 + 0.457V) µV (0.89 + 0.12 V) µV (9.4 + 0.12 V) µV (616 + 97 V) µV (1150 - 170 V) µV (-140 + 138 V) µV (-22 + 60 V) µV (-2380 + 110 V) µV (-7890 + 290) µV (2565 + 38 V) µV Fluke multi product calibrator 5522A AC Current – Generate 1A 10 Hz to 10 kHz (119 + 0.098 A) µA Fluke multi product calibrator 5522A Parameter/Equipment Range CMC2, 4, 5 (±) Comments Capacitance – Generate 220 pF to 11 nF Up to 3.3 μF (0.00276 + 0.00064 C) nF (-0.00085 + 0.0039 C) µF Fluke multi product calibrator 5522A Electrical Simulation of Thermocouples – Type K (-200 to 1372) °C (0.289 + 0.00059 Tp) °C Fluke multi product calibrator 5522A

(A2LA Cert. No. 4741.01) 09/26/2024 Page 4 of 5 III. Mechanical Parameter/Equipment Range CMC2, 3, 4 (±) Comments Torque – Measuring Equipment (1 to 10) ozf·in (10 to 50) ozf·in (5 to 50) lbf·in (25 to 250) lbf·in (15 to 150) lbf∙ft (100 to 2000) lbf∙ft 0.3 in-oz (0.025 + 0.0275 T) in-oz (0.8 - 0.0018 T) in-lbs (1.09 + 0.044 T) in-lbs (0.56 + 0.0036 T) ft-lbs (0.79 + 0.0033 T) ft-lbs Advanced witness systems display, loader, & transducers Tensiometer (Banding Tools) (40 to 200) lb (0.6 + 0.004 F) lbs EFG-Microprocessor force gauge IV. Time & Frequency Parameter/Equipment Range CMC2, 3, 4 (±) Comments Frequency – Measuring Equipment 10 Hz to 2 MHz (-0.012 + 0.002 Fr) Hz Fluke multi product calibrator 5522A __________________________ 1 This laboratory offers commercial calibration service. 2 Calibration and Measurement Capability Uncertainty (CMC) is the smallest uncertainty of measurement that a laboratory can achieve within its scope of accreditation when performing more or less routine calibrations of nearly ideal measurement standards or nearly ideal measuring equipment. CMCs represent expanded uncertainties expressed at approximately the 95 % level of confidence, usually using a coverage factor of k = 2. The actual measurement uncertainty of a specific calibration performed by the laboratory may be greater than the CMC due to the behavior of the customer’s device and to influences from the circumstances of the specific calibration. 3 The type of instrument or material being calibrated is defined by the parameter. This indicates the laboratory is capable of calibrating instruments that measure or generate the values in the ranges indicated for the listed measurement parameter.

(A2LA Cert. No. 4741.01) 09/26/2024 Page 5 of 5 4 In the statement of CMC, L is the numerical value of the nominal length of the device measured in inches. V is the numerical value for voltage in volts. A is the numerical value for current in amps. R is the numerical value for resistance in ohms. C is the numerical value for capacitance in farads. Tp is the numerical value for temperature in degrees Celsius. T is the numerical value for torque as specified by the unit indicated in the table above. F is the numerical value for force in pounds. Fr is the numerical value for frequency in hertz. 5 The stated measured values are determined using the indicated instrument (see Comments). This capability is suitable for the calibration of the devices intended to measure or generate the measured value in the ranges indicated. CMC’s are expressed as either a specific value that covers the full range or as a percent or fraction of the reading plus a fixed floor specification. 6 This scope meets A2LA’s P112 Flexible Scope Policy.

For the calibrations to which this accreditation applies, please refer to the laboratory’s Calibration Scope of Accreditation. Accredited Laboratory A2LA has accredited IMP ELECTRONIC SYSTEMS Hammond Plains, Nova Scotia, CANADA for technical competence in the field of Calibration This laboratory is accredited in accordance with the recognized International Standard ISO/IEC 17025:2017 General requirements for the competence of testing and calibration laboratories and R205 – Specific Requirements: Calibration Laboratory Accreditation Program. This accreditation demonstrates technical competence for a defined scope and the operation of a laboratory quality management system (refer to joint ISO-ILAC-IAF Communiqué dated April 2017). Presented this 26th day of September 2024. _______________________ Trace McInturff, Vice President, Accreditation Services For the Accreditation Council Certificate Number 4741.01 Valid to March 31, 2026